Hi all,
I'm having this issue with the CSR1000V and a topology with the bridge device for emulating a router on a stick environment. If I try to do the same config with IOL works fine. here the OS's details:
Any clue ?
thanks
R1#sh ver
Cisco IOS XE Software, Version 03.16.00.S - Extended Support Release
Cisco IOS Software, CSR1000V Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S, RELEASE SOFTWARE (fc6)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Sun 26-Jul-15 20:16 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2015 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
R1 uptime is 1 hour, 10 minutes
Uptime for this control processor is 1 hour, 12 minutes
System returned to ROM by reload
System image file is "bootflash:packages.conf"
Last reload reason: <NULL>
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
License Level: ax
License Type: Default. No valid license found.
Next reload license Level: ax
cisco CSR1000V (VXE) processor (revision VXE) with 1095671K/6147K bytes of memory.
Processor board ID 973PQJFGBXG
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
3022272K bytes of physical memory.
7774207K bytes of virtual hard disk at bootflash:.
Configuration register is 0x2102
R1#sh ip int brie
Interface IP-Address OK? Method Status Protocol
GigabitEthernet1 unassigned YES NVRAM up up
GigabitEthernet1.13 155.1.13.1 YES NVRAM up up
GigabitEthernet1.100 169.254.100.1 YES NVRAM up up
GigabitEthernet1.146 155.1.146.1 YES NVRAM up up
R1#
R1#sh arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 155.1.13.1 - 5000.000a.0000 ARPA GigabitEthernet1.13
Internet 155.1.146.1 - 5000.000a.0000 ARPA GigabitEthernet1.146
Internet 155.1.146.6 0 Incomplete ARPA
Internet 169.254.100.1 - 5000.000a.0000 ARPA GigabitEthernet1.100
R1#ping 169.254.100.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 169.254.100.2, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#ping 169.254.100.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 169.254.100.3, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)
R1#
CSR1000+Bridge or router on a stick
Moderator: mike
-
- Posts: 5083
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: CSR1000+Bridge or router on a stick
post topology pls
this image CSR is fine
this image CSR is fine
-
- Posts: 9
- Joined: Sun Mar 26, 2017 3:51 pm
Re: CSR1000+Bridge or router on a stick
hi,
you mean the topology lab ? or something else ?
now attached
you mean the topology lab ? or something else ?
now attached
You do not have the required permissions to view the files attached to this post.
-
- Posts: 5083
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: CSR1000+Bridge or router on a stick
Hi,
At least on my CSR 3.16.05 and EVE it works perfect.
I assume it is your image issue mate.
UD
At least on my CSR 3.16.05 and EVE it works perfect.
I assume it is your image issue mate.
UD
Code: Select all
R1#sh cdp neig
Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge
S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,
D - Remote, C - CVTA, M - Two-port Mac Relay
Device ID Local Intrfce Holdtme Capability Platform Port ID
R2 Gig 1 147 R I CSR1000V Gig 1
R3 Gig 1 169 R I CSR1000V Gig 1
Total cdp entries displayed : 2
R1#sh ip int brief
Interface IP-Address OK? Method Status Protocol
GigabitEthernet1 unassigned YES unset up up
GigabitEthernet1.100 169.254.100.1 YES manual up up
GigabitEthernet2 unassigned YES unset administratively down down
GigabitEthernet3 unassigned YES unset administratively down down
GigabitEthernet4 unassigned YES unset administratively down down
R1#ping 169.254.100.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 169.254.100.2, timeout is 2 seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 6/9/20 ms
R1#ping 169.254.100.3
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 169.254.100.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 18/92/169 ms
R1#
R1#sh vers
Cisco IOS XE Software, Version 03.16.05.S - Extended Support Release
Cisco IOS Software, CSR1000V Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.5(3)S5, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2017 by Cisco Systems, Inc.
Compiled Thu 19-Jan-17 09:11 by mcpre
R1#sh ip arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 169.254.100.1 - 500a.0001.0000 ARPA GigabitEthernet1.100
Internet 169.254.100.2 3 500a.0002.0000 ARPA GigabitEthernet1.100
Internet 169.254.100.3 3 500a.0003.0000 ARPA GigabitEthernet1.100