SW02(config)#int range eth1/2 - 3
SW02(config-if-range)#shut
SW02(config-if-range)#chan
SW02(config-if-range)#channel-g
SW02(config-if-range)#channel-group
*Aug 17 17:13:44.098: %LINK-5-CHANGED: Interface Ethernet1/2, changed state to administratively down
*Aug 17 17:13:44.107: %LINK-5-CHANGED: Interface Ethernet1/3, changed state to administratively down
*Aug 17 17:13:45.098: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/2, changed state to down
*Aug 17 17:13:45.114: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet1/3, changed state to down
SW02(config-if-range)#channel-group 50 mode on
Command rejected (Port-channel50, Et1/2): Invalid group(slot) number
% Range command terminated because it failed on Ethernet1/2
SW02(config-if-range)#
*Aug 17 17:13:47.568: EthChnl assert failure: (group >= 1) && (group <= FEC_MAX_GROUPS): ../switch/pagp/pagp_switch_private.c: 39
*Aug 17 17:13:47.568: -Traceback= 8842B4Bz A3CA29Bz A3CA4F1z A3D6E99z A3C6D77z A3C9288z A3D9823z 877EE93z 877E180z 877CB6Dz 8794C38z 8793BCFz
SW02(config-if-range)#exit
SW02(config)#defau
SW02(config)#default in
SW02(config)#default interface eth1/2
Interface Ethernet1/2 set to default configuration
SW02(config)#default interface eth1/3
Interface Ethernet1/3 set to default configuration
SW02(config)#int po50
^
% Invalid input detected at '^' marker.
SW02(config)#int p
SW02(config)#int por
SW02(config)#int port-c
SW02(config)#int port-channel ?
<1-64> Port-channel interface number
SW02(config)#int port-channel 50
^
% Invalid input detected at '^' marker.
SW02(config)#do show ethercha su
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
Number of channel-groups in use: 3
Number of aggregators: 3
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
10 Po10(SU) - Et0/0(P) Et0/1(P)
30 Po30(SU) - Et1/0(P) Et1/1(P)
40 Po40(SU) - Et0/2(P) Et0/3(P)
SW02(config)#int port-channel 50
^
% Invalid input detected at '^' marker.
SW02(config)#do show ver
Cisco IOS Software, Solaris Software (I86BI_LINUXL2-ADVENTERPRISE-M), Experimental Version 15.1(20131216:211730) [mmen 106]
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 16-Dec-13 13:50 by mmen
ROM: Bootstrap program is Linux
SW02 uptime is 1 hour, 30 minutes
System returned to ROM by reload at 0
System image file is "unix:/opt/unetlab/addons/iol/bin/i86bi-linux-l2-adventerprise-15.1b.b"
Last reload reason: Unknown reason
Linux Unix (Intel-x86) processor with 981578K bytes of memory.
Processor board ID 67108896
16 Ethernet interfaces
1024K bytes of NVRAM.
Configuration register is 0x0
SW02(config)#
Possible Layer 2 IOU bug?
Moderator: mike
-
- Posts: 533
- Joined: Wed Mar 15, 2017 1:54 pm
Re: Possible Layer 2 IOU bug?
when you try to create po 50 you got an error...
Later you put default config on interface dedicated for this PO
So normal if PO is absent....
E.
Later you put default config on interface dedicated for this PO
So normal if PO is absent....
E.