Cisco XRv 9000 ping neighbour ip address issue

[Kevin]

Hi,
I got my eve version 2.0.3-77 running in ESXi5.5 fine, also I loaded the cisco ASR 9000 software iosxrv-k9-demo-6.1.2 in eve.
The device boot up OK. after I configured the IP address, I am not able to ping the neighbour IP address. I have tried to link it to other IOU/IOL, vIOS, Dynamips images (Cisco IOS) device's interface. but still unable to ping the neighbour IP address.
Any one has the same problem in your eve lab?
I saw other people has the similar problem in GNS3 and got it fixed. Hope I do not have to go back to using GNS3.
for you easy to test, here is the link to download iosxrv-k9-demo-6.1.2 software.
https://drive.google.com/file/d/0B-73cX ... sp=sharing

Regards

Kevin

[ggcc]

Hi,
I got my eve version 2.0.3-77 running in ESXi5.5 fine, also I loaded the cisco ASR 9000 software iosxrv-k9-demo-6.1.2 in eve.
The device boot up OK. after I configured the IP address, I am not able to ping the neighbour IP address. I have tried to link it to other IOU/IOL, vIOS, Dynamips images (Cisco IOS) device's interface. but still unable to ping the neighbour IP address.
Any one has the same problem in your eve lab?
I saw other people has the similar problem in GNS3 and got it fixed. Hope I do not have to go back to using GNS3.
for you easy to test, here is the link to download iosxrv-k9-demo-6.1.2 software.
https://drive.google.com/file/d/0B-73cX ... sp=sharing

Regards

Kevin

Hi Kevin,

I just created and tested. I have no problem to ping.
-EVE-NG 2.0.3-71
-Two ASR 9000 software iosxrv-k9-demo-6.1.2 in eve
-One vIOS

Code: Select all

root@eve-ng:~/tmp# dpkg -l eve-ng
Desired=Unknown/Install/Remove/Purge/Hold
| Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend
|/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad)
||/ Name                   Version          Architecture     Description
+++-======================-================-================-==================================================
ii  eve-ng                 2.0.3-71         amd64            A new generation software for networking labs.

----------------------------------------------
RP/0/0/CPU0:xrv1#sh ver br
Sat Oct 14 21:30:25.907 UTC

Cisco IOS XR Software, Version 6.1.2[Default]
Copyright (c) 2016 by Cisco Systems, Inc.

ROM: GRUB, Version 1.99(0), DEV RELEASE

xrv1 uptime is 20 minutes
System image file is "bootflash:disk0/xrvr-os-mbi-6.1.2/mbixrvr-rp.vm"

cisco IOS XRv Series (Pentium Celeron Stepping 3) processor with 3145215K bytes of memory.
Pentium Celeron Stepping 3 processor at 2737MHz, Revision 2.174
IOS XRv Chassis

1 Management Ethernet
3 GigabitEthernet
97070k bytes of non-volatile configuration memory.
866M bytes of hard disk.
2321392k bytes of disk0: (Sector size 512 bytes).
RP/0/0/CPU0:xrv1#    
RP/0/0/CPU0:xrv1#sh ip int br
Sat Oct 14 21:30:35.726 UTC

Interface                      IP-Address      Status          Protocol Vrf-Name
MgmtEth0/0/CPU0/0              unassigned      Shutdown        Down     default 
GigabitEthernet0/0/0/0         192.168.12.1    Up              Up       default 
GigabitEthernet0/0/0/1         192.168.13.1    Up              Up       default 
GigabitEthernet0/0/0/2         unassigned      Shutdown        Down     default 
RP/0/0/CPU0:xrv1#ping 192.168.12.2
Sat Oct 14 21:30:44.685 UTC
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.12.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms
RP/0/0/CPU0:xrv1#ping 192.168.13.3
Sat Oct 14 21:30:55.485 UTC
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.13.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/9 ms
RP/0/0/CPU0:xrv1#

-----------------------
RP/0/0/CPU0:xrv2#sh ver br        
Sat Oct 14 21:35:23.536 UTC

Cisco IOS XR Software, Version 6.1.2[Default]
Copyright (c) 2016 by Cisco Systems, Inc.

ROM: GRUB, Version 1.99(0), DEV RELEASE

xrv2 uptime is 25 minutes
System image file is "bootflash:disk0/xrvr-os-mbi-6.1.2/mbixrvr-rp.vm"

cisco IOS XRv Series (Pentium Celeron Stepping 3) processor with 3145215K bytes of memory.
Pentium Celeron Stepping 3 processor at 2704MHz, Revision 2.174
IOS XRv Chassis

3 GigabitEthernet
1 Management Ethernet
97070k bytes of non-volatile configuration memory.
866M bytes of hard disk.
2321392k bytes of disk0: (Sector size 512 bytes).
RP/0/0/CPU0:xrv2# 
RP/0/0/CPU0:xrv2#sh ip int br
Sat Oct 14 21:35:28.906 UTC

Interface                      IP-Address      Status          Protocol Vrf-Name
MgmtEth0/0/CPU0/0              unassigned      Shutdown        Down     default 
GigabitEthernet0/0/0/0         192.168.12.2    Up              Up       default 
GigabitEthernet0/0/0/1         unassigned      Up              Up       default 
GigabitEthernet0/0/0/2         unassigned      Shutdown        Down     default 
RP/0/0/CPU0:xrv2#
RP/0/0/CPU0:xrv2#ping 192.168.12.1
Sat Oct 14 21:35:36.595 UTC
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.12.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
RP/0/0/CPU0:xrv2#

------------------------------------------------------

vIOS3#sh ver  
Cisco IOS Software, IOSv Software (VIOS-ADVENTERPRISEK9-M), Version 15.6(2)T, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Tue 22-Mar-16 16:19 by prod_rel_team


ROM: Bootstrap program is IOSv

vIOS3 uptime is 20 minutes
System returned to ROM by reload
System image file is "flash0:/vios-adventerprisek9-m"
Last reload reason: Unknown reason



This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to
export@cisco.com.

Cisco IOSv (revision 1.0) with  with 460153K/62464K bytes of memory.
Processor board ID 9A7VMWFH5C12AYNLK0THQ
4 Gigabit Ethernet interfaces
DRAM configuration is 72 bits wide with parity disabled.
256K bytes of non-volatile configuration memory.
2097144K bytes of ATA System CompactFlash 0 (Read/Write)
0K bytes of ATA CompactFlash 1 (Read/Write)
0K bytes of ATA CompactFlash 2 (Read/Write)
0K bytes of ATA CompactFlash 3 (Read/Write)



Configuration register is 0x0

vIOS3#
vIOS3#sh ip int br
Interface                  IP-Address      OK? Method Status                Protocol
GigabitEthernet0/0         192.168.13.3    YES manual up                    up      
GigabitEthernet0/1         unassigned      YES unset  administratively down down    
GigabitEthernet0/2         unassigned      YES unset  administratively down down    
GigabitEthernet0/3         unassigned      YES unset  administratively down down    
vIOS3#ping 192.168.13.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.13.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 2/2/3 ms
vIOS3#

[Kevin]

Hi, ggcc
Thank your help for the testing.
I found my problem, I used the wrong import template. should be Cisco XRv not the Cisco XRv 9000.
All working now.
Regards
Kevin