Level 3 switch in EVE-NG
Moderator: mike
-
- Posts: 4
- Joined: Sat May 06, 2017 1:12 pm
Level 3 switch in EVE-NG
Hi guys.
What images can be used for Level 3 switching?
Thank you.
What images can be used for Level 3 switching?
Thank you.
-
- Posts: 409
- Joined: Sun Mar 19, 2017 10:27 pm
-
- Posts: 4
- Joined: Sat May 06, 2017 1:12 pm
Re: Level 3 switch in EVE-NG
Hi ramindia,
I tried IOL i86bi-linux-l3-adventerprisek9-15.2.2.03T.bin.
However, there are no switch commands in it.
It works anly as a router.
Could you please explain in more detail how to configure it to act as L3 switch.
Thank you.
I tried IOL i86bi-linux-l3-adventerprisek9-15.2.2.03T.bin.
However, there are no switch commands in it.
It works anly as a router.
Could you please explain in more detail how to configure it to act as L3 switch.
Thank you.
-
- Posts: 409
- Joined: Sun Mar 19, 2017 10:27 pm
Re: Level 3 switch in EVE-NG
Full Blown features of L2/L3 i use normally Arista Switch for my Labs, but you can use Cisco vIOS L2 image (not tested myself full features).
R!
-
- Posts: 5084
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Level 3 switch in EVE-NG
mentinoned bove is L3 router image.
You have ti find images which contains L2 in the name. It is switch image and does support L3 features
You have ti find images which contains L2 in the name. It is switch image and does support L3 features
-
- Posts: 4
- Joined: Sat May 06, 2017 1:12 pm
Re: Level 3 switch in EVE-NG
Hi guys,
At the moment I use i86bi-linux-l2-adventerprisek9-15.2d.bin for Layer 3 switching.
Today I came across with the following issue.
The command ip routing is accepted though is not shown in the show running-config output.
I was able to configure EIGRP between MLS and RTR.
Traffic is successfully transmitted from SRV to both VLAN 2 and VLAN 3 interfaces on MLS (Layer 3 switch) and vice versa.
However, traffic is not transmitted neither to and from PC1 and PC2 not between PC1 and PC2 (inter-vlan traffic).
Below is the config of MLS (Layer 3 switch).
Could you guys please check if I missed something in configuration or there is something with IOU image.
Thank you.
At the moment I use i86bi-linux-l2-adventerprisek9-15.2d.bin for Layer 3 switching.
Today I came across with the following issue.
The command ip routing is accepted though is not shown in the show running-config output.
I was able to configure EIGRP between MLS and RTR.
Traffic is successfully transmitted from SRV to both VLAN 2 and VLAN 3 interfaces on MLS (Layer 3 switch) and vice versa.
However, traffic is not transmitted neither to and from PC1 and PC2 not between PC1 and PC2 (inter-vlan traffic).
Below is the config of MLS (Layer 3 switch).
Code: Select all
MLS#sh run
Building configuration...
Current configuration : 1271 bytes
!
! Last configuration change at 15:31:31 EET Tue May 16 2017
!
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
!
hostname MLS
!
boot-start-marker
boot-end-marker
!
no aaa new-model
clock timezone EET 2 0
!
ip cef
no ipv6 cef
!
spanning-tree mode rapid-pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
interface Ethernet0/0
no switchport
ip address 10.10.10.254 255.255.255.0
duplex auto
!
interface Ethernet0/1
switchport access vlan 2
switchport mode access
spanning-tree portfast edge
!
interface Ethernet0/2
switchport access vlan 3
switchport mode access
spanning-tree portfast edge
!
interface Ethernet0/3
!
interface Vlan2
ip address 190.200.250.33 255.255.255.224
!
interface Vlan3
ip address 190.200.250.65 255.255.255.224
!
router eigrp 650
network 10.10.10.0 0.0.0.255
network 190.200.250.32 0.0.0.31
network 190.200.250.64 0.0.0.31
eigrp router-id 3.3.3.3
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
control-plane
!
line con 0
exec-timeout 0 0
logging synchronous
line aux 0
line vty 0 4
exec-timeout 0 0
login
!
end
Thank you.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 12
- Joined: Tue Jun 06, 2017 10:31 am
Re: Level 3 switch in EVE-NG
I used 3725 xxx .images as a L3 switch on windows but it's not working. Cannot ping between switches.
Wht shld i do? Thanks
Wht shld i do? Thanks
-
- Posts: 5084
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Level 3 switch in EVE-NG
3725 as SW works like charm sir:)
just remeber to add etherswitch card on each 3725, and switchports are from f1/0-15
just remeber to add etherswitch card on each 3725, and switchports are from f1/0-15
You do not have the required permissions to view the files attached to this post.
-
- Posts: 12
- Joined: Tue Jun 06, 2017 10:31 am
Re: Level 3 switch in EVE-NG
Of course, i surely did.
Plz see attached photo.
Something is wrong in using eve coz can ping between SVI in packet tracer or gns3.
Plz guide me how do i use L3 switch in EVE.
I just started using eve. This is my frist lab.
My image is corect?
Windows 10
VM - Ubuntu 10.xx
Plz see attached photo.
Something is wrong in using eve coz can ping between SVI in packet tracer or gns3.
Plz guide me how do i use L3 switch in EVE.
I just started using eve. This is my frist lab.
My image is corect?
Windows 10
VM - Ubuntu 10.xx
You do not have the required permissions to view the files attached to this post.