Hi folks,
i have setup a SDWAN in eve pro, i have installed vedge , vedge(ver:20.7.1) is directly connected to vSwitch (vios_l2_advancek9, ver 15.2), i have made one of vSwith port as routed port and connected to vedge but not i am unable to ping, though physical port is up/up on vedge as well on vSwitch, i tried changing switch port/ new switch but nothing seems working,
Vedge11# show int ge0/2
interface vpn 1 interface ge0/2 af-type ipv4
ip-address 10.11.100.11/24
if-admin-status Up
if-oper-status Up
if-tracker-status NA
encap-type null
port-type service
mtu 1500
hwaddr 50:11:00:0b:00:03
speed-mbps 1000
duplex full
tcp-mss-adjust 1416
uptime 0:21:46:23
rx-packets 0
tx-packets 25
SITE-11_SWITCH-19#show run int gi0/2
Building configuration...
Current configuration : 108 bytes
!
interface GigabitEthernet0/2
no switchport
ip address 10.11.100.19 255.255.255.0
negotiation auto
end
SITE-11_SWITCH-19#show int gi0/2
GigabitEthernet0/2 is up, line protocol is up (connected)
Hardware is iGbE, address is 5011.0013.0002 (bia 5011.0013.0002)
Internet address is 10.11.100.19/24
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto Duplex, Auto Speed, link type is auto, media type is RJ45
can someone please check and confirm ?
Unable to Ping Vedge to Vswitch
Moderator: mike
-
- Posts: 4
- Joined: Fri Apr 08, 2022 2:29 pm
Re: Unable to Ping Vedge to Vswitch
can anyone pls help, i am unable to run a environment where two vedge are connected to a single distribution switch over L3 links ,
May be Mike/UD if you see the post and can help ?
May be Mike/UD if you see the post and can help ?
-
- Posts: 5084
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Unable to Ping Vedge to Vswitch
We are on EVE live chat..
and it is 100% not eve issue you cannot ping..but mostly issue is where you got viptela images and how did you load it in eve...
Also it can be config issue between your vedge and switch....
no matter it is L2 or L3
and it is 100% not eve issue you cannot ping..but mostly issue is where you got viptela images and how did you load it in eve...
Also it can be config issue between your vedge and switch....
no matter it is L2 or L3
-
- Posts: 4
- Joined: Fri Apr 08, 2022 2:29 pm
Re: Unable to Ping Vedge to Vswitch
thank you for your response UD, it was working when i was connecting Vios router but did not worked when i used vIOS Switch,
this made me to think what does the router do but switch do not , and i could able to figured it out, this issue stand close, thanks again.
this made me to think what does the router do but switch do not , and i could able to figured it out, this issue stand close, thanks again.
-
- Posts: 4
- Joined: Fri Apr 08, 2022 2:29 pm
Re: Unable to Ping Vedge to Vswitch
thank you for your response UD, it was working when i was connecting Vios router but did not worked when i used vIOS Switch,
this made me to think what does the router do but switch do not , and i could able to figured it out, this issue stand close, thanks again.
this made me to think what does the router do but switch do not , and i could able to figured it out, this issue stand close, thanks again.
-
- Posts: 5084
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Unable to Ping Vedge to Vswitch
works on both switch and router.
I just prefer use nit vIOS but IOL
it has better performance than vIOS
I just prefer use nit vIOS but IOL
it has better performance than vIOS