Before posting something, READ the changelog, WATCH the videos, howto and provide following:
Your install is: Bare metal, ESXi, what CPU model, RAM, HD, what EVE version you have, output of the uname -a and any other info that might help us faster.
Moderator: mike
-
smilodon
- Posts: 1
- Joined: Tue Oct 16, 2018 7:02 pm
Post
by smilodon » Tue Oct 16, 2018 8:08 pm
Hello,
i dont have access through cloud from CSR1000V in EVE - NG Lab to mikrotik router in real network. I see correct mac addresses on eve ng Ubuntu VM, but cannt ping from csr to mikrotik. Eve - NG deployed on esxi 6.0 hypervisor, promiscous mode enabled.
Mac table from Eve NG VM
Code: Select all
brctl showmacs pnet0
2 50:00:00:01:00:00 no 1.17
1 e4:8d:8c:d3:b4:8d no 0.00
50:00:00:01:00:00 - csr100v in eve-ng lab
e4:8d:8c:d3:b4:8d - mikrotik router in real network
from CSR
Code: Select all
R1#ping 192.168.88.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.88.1, timeout is 2 seconds:
...
Success rate is 0 percent (0/3)
R1#show arp
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.1.2.1 - 5000.0001.0001 ARPA GigabitEthernet2
Internet 10.10.10.10 - 5000.0001.0002 ARPA GigabitEthernet3
Internet 192.168.88.1 0 e48d.8cd3.b48d ARPA GigabitEthernet1
Internet 192.168.88.100 - 5000.0001.0000 ARPA GigabitEthernet1
from mikrotik
Code: Select all
D E 50:00:00:01:00:00 ether4-slave-local bridge-local
DL E4:8D:8C:D3:B4:8D bridge-local bridge-local
-
adirbd
- Posts: 2
- Joined: Sun Sep 22, 2019 7:42 am
Post
by adirbd » Sun Sep 22, 2019 7:54 am
Hi, I have the same problem. I have arp in both sides and the router in the lab get DHCP from my local router but I can't ping.
it's like only layer 2 work to the outside but no layer 3.
-
Uldis (UD)
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
-
Contact:
Post
by Uldis (UD) » Sun Sep 22, 2019 8:05 am
It depends whwre is your EVE installed?
If it is on esxi it can be 2 reasons:
1. Promiscue mode is not enabled on VMnet in the ESXi, Enable Promiscue mode on Esxi vSwitch associated with Vmnet EVE management
2. You had Team paired NIC on esxi, remoe it, use single cable/NIC, no NIC Teaming
Rest issues usually are FW blocking on home routers etc
Uldis
-
adirbd
- Posts: 2
- Joined: Sun Sep 22, 2019 7:42 am
Post
by adirbd » Sun Sep 22, 2019 8:22 am
I use VMware Workstation, and when I use VM network card that works with nat it's work and then I have a ping, but I want to access from my real network to the devices.
firewall is disabled.
Promiscue mode is enabled.
-
Uldis (UD)
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
-
Contact:
Post
by Uldis (UD) » Mon Sep 23, 2019 7:02 am
It depends from your PC NIC card where the VM ware workstation is installed !
For example some laptop wifi NICs simply are not supported by vm ware and cannot be used bridged way.
Usually ethernet NIC is supported by vm ware, and that is your gateway to real lan.
All of this is explained in EVE Cookbook section 10.
https://www.eve-ng.net/images/EVE-COOK-BOOK-1.13.pdf
Uldis