I have just installed the community edition over a fresh ubuntu 16.04 LTS install.
I want to double attach my eve-ng server to a physical cisco switch with LACP.
In the future, the eve-ng server would be installed on a vPC ( of 2 nexus ), with LACP.
I need to be able to patch my physical cisco switches without loosing connectivity to my eve-ng server.
I never managed to get LACP packets between my bond0 interface ( eth0 and eth1 bridged ) and my cisco switch.
My cisco setup :
Code: Select all
#show running-config interface gigabitEthernet 0/5
Building configuration...
Current configuration : 116 bytes
!
interface GigabitEthernet0/5
switchport access vlan 10
switchport mode access
channel-group 1 mode active
end
#show running-config interface gigabitEthernet 0/6
Building configuration...
Current configuration : 116 bytes
!
interface GigabitEthernet0/6
switchport access vlan 10
switchport mode access
channel-group 1 mode active
end
#show running-config interface port-channel 1
Building configuration...
Current configuration : 82 bytes
!
interface Port-channel1
switchport access vlan 10
switchport mode access
end
# cat /etc/network/interfaces
Code: Select all
# The primary network interface
allow hotplug eth0
iface eth0 inet manual
bond-master bond0
allow hotplug eth1
iface eth1 inet manual
bond-master bond0
auto bond0
iface bond0 inet manual
bond-mode 4
bond-miimon 100
bond-lacp-rate 1
bond-slaves none
auto pnet0
iface pnet0 inet static
address 10.156.232.74
netmask 255.255.248.0
gateway 10.156.239.254
dns-domain labs.arkea.com
dns-nameservers 10.154.30.4 10.154.99.65
bridge_ports bond0
bridge_stp off
Feb 26 10:59:27.024: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to down
Feb 26 10:59:27.146: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to down
Feb 26 11:46:39.322: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to up
Feb 26 11:46:39.525: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to up
Feb 26 11:46:45.362: %EC-5-L3DONTBNDL2: Gi0/5 suspended: LACP currently not enabled on the remote port.
Feb 26 11:46:46.068: %EC-5-L3DONTBNDL2: Gi0/6 suspended: LACP currently not enabled on the remote port.
Feb 26 11:47:01.206: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to down
Feb 26 11:47:01.206: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to down
Feb 26 11:47:04.247: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to up
Feb 26 11:47:04.250: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to up
Feb 26 11:47:10.863: %EC-5-L3DONTBNDL2: Gi0/6 suspended: LACP currently not enabled on the remote port.
Feb 26 11:47:11.125: %EC-5-L3DONTBNDL2: Gi0/5 suspended: LACP currently not enabled on the remote port.
Feb 26 11:47:13.645: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to down
Feb 26 11:47:13.649: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to down
Feb 26 11:47:16.648: %LINK-3-UPDOWN: Interface GigabitEthernet0/5, changed state to up
Feb 26 11:47:16.651: %LINK-3-UPDOWN: Interface GigabitEthernet0/6, changed state to up
Feb 26 11:47:22.443: %EC-5-L3DONTBNDL2: Gi0/6 suspended: LACP currently not enabled on the remote port.
Feb 26 11:47:22.460: %EC-5-L3DONTBNDL2: Gi0/5 suspended: LACP currently not enabled on the remote port.
i have tried a setup from this page :
http://www.thingnetwork.io/working-with ... and-wlan0/
Still the same issue.
Any advice ?