CISCO IOSv2 Infiniti boot loop

Before posting something, READ the changelog, WATCH the videos, howto and provide following:
Your install is: Bare metal, ESXi, what CPU model, RAM, HD, what EVE version you have, output of the uname -a and any other info that might help us faster.

Moderator: mike

Post Reply
SirStephanikus
Posts: 3
Joined: Tue May 19, 2020 5:14 pm

CISCO IOSv2 Infiniti boot loop

Post by SirStephanikus » Tue May 19, 2020 5:34 pm

Hello,

I am trying out EVE-NG and compare it directly to the new Cisco CML 2.
However, as a first start I uploaded these 2 Images to /opt/unetlab/addons/qemu
and in their subdirs:
-- viosl2-adventerprisek9-m.SSA.high_iron_20180619/
-- viosl2-adventerprisek9-m.ssa.high_iron_20190423/


Later I renamed the qcow2 files to virtioa.qcow2 and ran this /opt/unetlab/wrappers/unl_wrapper -a fixpermissions.

EVE-NG directly recognize these images and I gave the Node 24 NICS ....on startup it runs than in an infinity boot loop like this:

Code: Select all

error: Can't get controller info..
error: Can't get controller info.Booted IOSv. Boot args: [/vios_l2-adventerprisek9-m]

Smart Init is enabled

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco IOS Software, vios_l2 Software (vios_l2-ADVENTERPRISEK9-M), Version 15.2(CML_NIGHTLY_20180619)FLO_DSGS7, EARLY DEPLOYMENT DEVELOPMENT BUILD, synced to  V152_6_0_81_E
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2018 by Cisco Systems, Inc.
Compiled Tue 19-Jun-18 06:06 by mmen

<some bla bla>


CPU exception occurred: General protection fault(13) (SIGBUS, 13, 0xD)


 17:25:51 UTC Tue May 19 2020: Unexpected exception to CPU: vector D, PC/EIP = 0x127E24F 

-Traceback= 127E24F 1468DEC 

CPU Register Context:
EAX = 0x1D1C56A0  ECX     = 0xA0561C1D  EDX = 0x00000000  EBX  = 0x00000004
ESP = 0x1B783B44  EBP     = 0x1B783B74  ESI = 0x1B783BB0  EDI  = 0x03000000
EIP = 0x0127E24F  EFLAGS  = 0x00010216  CS  = 0x00000008  SS   = 0x00000010
DS  = 0x00000010  ES      = 0x00000010  FS  = 0x00000010  GS   = 0x00000010

Writing crashinfo to flash0:crashinfo_20200519-172551-UTC


When I remove the NICs and give them only 4 Nics, the node starts just fine.

What did I wrong ?
  • Wrong Settings like the qemu version ?
  • How can I get 24 Ports and in normal iteration like 0/1 - 0/24

Uldis (UD)
Posts: 3188
Joined: Wed Mar 15, 2017 4:44 pm
Location: London
Contact:

Re: CISCO IOSv2 Infiniti boot loop

Post by Uldis (UD) » Tue May 19, 2020 5:51 pm

vIOS supports up to 16 ports only

IOL switch supports more..
6x4port vards gives 24 ports, IOL !!!

Post Reply