Juniper vMX issues after Pro Upgrade
Moderator: mike
-
- Posts: 14
- Joined: Mon Aug 16, 2021 1:01 pm
Juniper vMX issues after Pro Upgrade
Since upgrade to 5.0.1-14-PRO I have been unable to run any vMX nodes and receive the below errors once device is booted. I have also done a clean install and still get the errors. I can login as root but the 'cli' command doesn't work. Am running Eve in ESXi.
g_vfs_done():md9.uzip[READ(offset=622983168, length=2048)]error = 86
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=622985216, length=8192)]error = 86
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46307328, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46651392, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46659584, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46675968, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
Help please!
g_vfs_done():md9.uzip[READ(offset=622983168, length=2048)]error = 86
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=622985216, length=8192)]error = 86
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46307328, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46651392, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46659584, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
g_vfs_done():md9.uzip[READ(offset=46675968, length=2048)]error = 86
vm_fault: pager read error, pid 6485 (cli)
md9.uzip: UZIP(zlib) inflate() failed
Help please!
-
- Posts: 14
- Joined: Mon Aug 16, 2021 1:01 pm
Re: Juniper vMX issues after Pro Upgrade
and the REs of vQFXs won't start either (Junos 17.3)
-
- Posts: 5080
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: Juniper vMX issues after Pro Upgrade
Might be you can try,
wipe node/start
but anyway this lab before is running vQFX vers 20.3
EVE V5 Pro
but vMX I dorecommend to use Versions 18-21
tbh 18 was best
wipe node/start
but anyway this lab before is running vQFX vers 20.3
EVE V5 Pro
but vMX I dorecommend to use Versions 18-21
tbh 18 was best
You do not have the required permissions to view the files attached to this post.
-
- Posts: 14
- Joined: Mon Aug 16, 2021 1:01 pm
Re: Juniper vMX issues after Pro Upgrade
have tried and wiping the nodes but makes no difference. I am running 18.2 and had no issues before the upgrade. vQFX is 17.3 but that was on the advise of Christian @ Juniper as newer versions boot into the line card not master when rebooted
-
- Posts: 14
- Joined: Mon Aug 16, 2021 1:01 pm
Re: Juniper vMX issues after Pro Upgrade
it's definitely an issue with the version 5. The nodes run without issue on version 4 so am going to stick with that
-
- Posts: 5080
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
-
- Posts: 14
- Joined: Mon Aug 16, 2021 1:01 pm
Re: Juniper vMX issues after Pro Upgrade
I still experiencing this issue. Seems to happen when I start a few vMXs at same time. Pain in the backside having to start them all individually and not something I had to do on previous Pro version
-
- Posts: 48
- Joined: Thu Dec 19, 2019 4:49 pm
Re: Juniper vMX issues after Pro Upgrade
For my information, doesn't the delay option in the node parameter help ? Even with a short 30sec delay between each node ?