How can I connect to the network cloud to get internet ping 8.8.8.8 to the internet? Currently, I am using Managment Cloud 0 for managing all my devices. For this reason, I can't use it again. Cloud 0 for the internet . Isnt it ?
I attach my topology
https://ibb.co/XyQvMWg
someone can i help me
Moderator: mike
-
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: someone can i help me
Cloud1 for sure has no internet.
But if your cloud0 is NAT network on vm ware it should have internet
but then you must properly configure your lab
But if your cloud0 is NAT network on vm ware it should have internet
but then you must properly configure your lab
-
- Posts: 3
- Joined: Fri Jun 03, 2022 7:52 am
Re: someone can i help me
So, thanks for your reply.
Yes, I know
I will try to explain my case to you. I am trying to get internet access through from internet zone. This zone has a cloud 1 configured HOST-ONLY (DHCP Automatic). So for this reason, when I am configuring the interface router fa1/0, the interface hits against host-only and obteins the ip 192.168.226.x without internet. In my scenario, how can I get an internet connection adaptor host-only? there any special configuration of the virtual editor network to make this connection possible? So I have CLOUD 0 MGMNT for managing my devices and CLOUD 1 to connect to the internet.
If I put the cloud 0 (management) in this zone, it works fine, but it is assigned the ranges managements devices IP. I want to get a different ip address to go out to internet
FastEthernet1/0 192.168.2.145 YES DHCP up up
NVI0 192.168.4.1 YES unset up up
ROU-INT> show ip inter bri
ROU-INT> show ip inter brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.4.1 YES NVRAM up up
FastEthernet1/0 192.168.2.145 YES DHCP up up
NVI0 192.168.4.1 YES unset up up
ROU-INT>show ip ro
ROU-INT>show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, + - replicated route
Gateway of last resort is 192.168.2.2 to network 0.0.0.0
S* 0.0.0.0/0 [254/0] via 192.168.2.2
I attach you my escenario
https://ibb.co/xC30SZ3
Yes, I know
I will try to explain my case to you. I am trying to get internet access through from internet zone. This zone has a cloud 1 configured HOST-ONLY (DHCP Automatic). So for this reason, when I am configuring the interface router fa1/0, the interface hits against host-only and obteins the ip 192.168.226.x without internet. In my scenario, how can I get an internet connection adaptor host-only? there any special configuration of the virtual editor network to make this connection possible? So I have CLOUD 0 MGMNT for managing my devices and CLOUD 1 to connect to the internet.
If I put the cloud 0 (management) in this zone, it works fine, but it is assigned the ranges managements devices IP. I want to get a different ip address to go out to internet
FastEthernet1/0 192.168.2.145 YES DHCP up up
NVI0 192.168.4.1 YES unset up up
ROU-INT> show ip inter bri
ROU-INT> show ip inter brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0/0 192.168.4.1 YES NVRAM up up
FastEthernet1/0 192.168.2.145 YES DHCP up up
NVI0 192.168.4.1 YES unset up up
ROU-INT>show ip ro
ROU-INT>show ip route
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, + - replicated route
Gateway of last resort is 192.168.2.2 to network 0.0.0.0
S* 0.0.0.0/0 [254/0] via 192.168.2.2
I attach you my escenario
https://ibb.co/xC30SZ3
-
- Posts: 5081
- Joined: Wed Mar 15, 2017 4:44 pm
- Location: London
- Contact:
Re: someone can i help me
My friend, I suppose about NAT feature on the router
inside to outside, and you can have any subnet out to the internet
CCNA task
inside to outside, and you can have any subnet out to the internet
CCNA task